Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

企业以顾客为中心的营销策略过程研究

试图构建企业以顾客为中心的营销策略过程的一般模型，并利用已有的研究成果对其构成要素进行了深入分析．在此基础上，对此模型所形成的企业营销策略循环进行分类分析，并以实例说明它们所代表的现实意义，从而为企业的决策提供帮助．     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.     

DESIGN AND IMPLEMENTATION OF STATE OBSERVERS IN REACTIVE DISTILLATION

This study demonstrates that state observers can be developed and applied to infer the composition profiles of reactive distillation columns from noise-contaminated temperature measurements. The design and implementation of a Kalman filter (KF) and a Luenberger observer (LO) are carried out, and their performances are quantitatively assessed. The reliability, accuracy, and robustness of the two designs method are examined and compared quantitatively. The design and implementation of a Luenberger observer are simpler and easier to carry out than those of a Kalman filter. On the other hand, a Kalman filter is found to be more robust to a noisy measurements, erroneous initial estimates, and model uncertainties. A Luenberger observer could be used for composition estimation of reactive distillation when an ideal model of the system can reasonably approximate the real system; otherwise, a Kalman filter is recommended to be applied in more practical situations.     

The impact of roasting on the ochratoxin A content of coffee

Roasting coffee led to a drop in the ochratoxin A (OTA) concentration, as measured by the reference method, especially for dark type roasts. The way the beverage was prepared also affected the OTA content, which could paradoxically be higher than that of the initial roasted coffee. Assays on the thermal stability of pure OTA showed that it ought to be found in larger quantities in roasted coffee. This suggested that OTA was masked by reactions with the substrate during roasting. The absence of OTA in green coffee is therefore the best guarantee of safety.     

An Agent Interaction Based Method for Nonlinear Process Plan Scheduling

This article puts forward a scheduling method for nonlinear process plan shop floor.Task allocation and load bal- ance are realized by bidding mechanism.Though the agent interaction process,the execution of tasks is determined and the coherence of manufacturing decision is verified.The employment of heuristic index can help to optimize the system performance.     

Logistic Regression Analysis of Customer Satisfaction Data

Variation exists in all processes. Significant work has been done to identify and remove sources of variation in manufacturing processes resulting in large returns for companies. However, business process optimization is an area that has a large potential return for a company. Business processes can be difficult to optimize due to the nature of the output variables associated with them. Business processes tend to have output variables that are binary, nominal or ordinal. Examples of these types of output include whether a particular event occurred, a customer's color preference for a new product and survey questions that assess the extent of the survey respondent's agreement with a particular statement. Output variables that are binary, nominal or ordinal cannot be modeled using ordinary least‐squares regression. Logistic regression is a method used to model data where the output is binary, nominal or ordinal. This article provides a review of logistic regression and demonstrates its use in modeling data from a business process involving customer feedback. Copyright © 2006 John Wiley & Sons, Ltd.     

提高塑封双列直插式光耦合器绝缘耐压的设计和工艺要点

介绍了研制出其性能达国际先进公司同类产品水平的塑封双列直插式光耦合器的工作原理和提高绝缘耐压的技术难点，从引线框架设计、加工精度控制、内包封材料选型、理想内包封形状控制、塑封气密性的实现、环境条件的完善等方面讨论了提高绝缘耐压的设计和工艺要点。